Danfoss eka 164a manual
DANFOSS EKA 164A MANUAL >> READ ONLINE
EKA 164A, Display, Universal settings, Packing format: Multi pack, Quantity per packing format: 30 Contact + Add to comparison list - Remove from comparison list. Danfoss EKC 202D1 temperature settings. I need some help on this danfoss EKC 202D1. Its controlling a small freezer unit. The set-point temperature is -18º. The R1 seting is AKS 32R, NSK AKS 21, AKS 11 EKA 164A EKA 183A Data Manual Superheat controller type EKD 316 ©Danfoss A/S (AC-MCI / sw), 2014-10 DKRCC.PS.RP0.A2.02 / 520H9139 5 Necessary connections Terminals: 1-2 Supply voltage 24 V a.c./d.c. 3-4 Battery (the voltage will close the ETS valve if the controller losses its supply voltage). External display • One display type EKA 163A or 164A can be connected. • If an external display is connected to the controller, data commu- nication can also be connected, though this requires the installa- tion of a separate data communication module. See also page 23. Coordinated defrost Modbus version Type EKD 316C (Colibri®) The battery voltage must be kept disconnected from terminals 1 and 2. 5-8 Supply to step motor 9-13 Operation via data communication EITHER EKA 164A OR System unit + software It is important that the installation of the data communi - cation cable be done correctly. Terminal 56 = screen Terminal 57 = A+ Terminal 58 = B- (Alternatively the terminals can be connected to an external display type EKA 163A or 164A, but then they cannot be used for data communication. Any data communication must then be carried out by one of the other methods.) Supply voltage 230 V a.c., 50/60 Hz Connections The EKD 316 controller is compatible with all Danfoss ETS and KVS valves. It is designed speci cally for evaporator control in water chillers and rooftop units. Only parameters needed for those applications are shown in the menus. Once the parameters are set with an EKA 164A Universal Setting Module, they can Danfoss | DCS (sw) |2016.08 DKRCC.PI.RP0.B6.51 | 2 L = max. 1000 m EKA 164A EKD 316 Danf oss M84_0010_ 1 24V 18V Valve connection Ventiltilslutning Ventil Anschluß ETS / KVS / CCMT / CTR White Hvid Weiß 5 Black Sort Schwarz 6 Red Rød Rot 7 Green Grøn Grün 8 ETS 6 Orange Orange Orange 5 Yellow Gul Gelb 6 Red Rød Rot 7 Black Sort Schwarz 8 EKA Display If there is be external reading/operation of the controller, display type EKA 163B or EKA 164B can be connected. RS485 (terminal 51, 52, 53) For data communication, but only if a data communication module is inserted in the controller. The module can be a LON RS485, DANBUSS or a MODBUS. Terminal 51 = screen Terminal 52 = A (A+) EKA 164A Par les pinces à vis EKA 163B EKA 164B Connecteur Ambiance-10 à +55°C, Fonctionnement-40 à +70°C, Transport Humidité relative de 20 à 80%, non condensante Danfoss et le logotype Danfoss sont des marques de fabrique de Danfoss A/S. Tous droits réservés. Created Date: 2/7/2007 7:45:03 AM Mutli-function tool for manual operation 027H0181 Description Danfoss Code No. AST-G Service Driver; used to manually open or close valve 034G0013 M12 cable, Permits wire runs of up to 328 ft. 084B2238 EKD 316—valve driver or superheat controller 084B8040 EKA 164A—display and control buttons for EKD 316 084B8563 CCMT Spare Parts and display type EKA 163A or 164A, but then they cannot be used for data communication. Any data communication must then be carried out by one of the other methods.) Supply voltage 230 V a.c., 50/60 Hz DO1 Connection of solenoid valve or relay for compressor. The coil must be a 230 V a.c. coil. DO2 Alarm There is a connection between terminal 7 and display type EKA 163A or 164A, but then they cannot be used for data communication. Any data communication must then be carried out by one of the other methods.) Supply voltage 230 V a.c., 50/60 Hz DO1 Connection of solenoid valve or relay for compressor. The coil must be a 230 V a.c. coil. DO2 Alarm There is a connection between terminal 7 and type EKA 163A or 164A, but then they cannot be used for datacommunication. Any communication must then be Danfoss wil not be responsible for any goods, or plant compo- nents, damaged as a result of the above defects. Manual service, stop regulation, start regulation (-1, 0, 1) r12 1-1 0 The EKA 164A will talk with the EKD 316 which has Modbus comms. The EXD version is for OEMs which use the Canbus comms protocol as a preference. Each manufacturer has their own software demands and hence component manufacturers make specific types for what each manufacturer demands. danfoss eka 164a manual Controller for operation of evaporator on water chiller. EKD 316. Manual EKC State. (0 = regulation). S10: Refrigeration stopped by the internal or external Controller for controlling one evaporator. EKC 414A1. Manual EKA 162. Delay on temperature alarm.
632, 843, 884, 347, 464.
0コメント